Valworx 568210C electric actuated 3-way L-port lead free ball valve is used to control the flow of water, air, oil, and other media compatible with the materials of construction. Ideal where lead free and NSF approved construction are required for potable drinking water as well as other industrial applications. These FULL PORT valves can be used as either a diverter valve or selector valve. There is no flow shutoff position with this type valve. Actuator uses power-to-open (position 2) and power-to-close (position 1), stays in last known position with loss of power. On receipt of a continuous voltage signal, the motor runs and via a self-locking gear drive rotates the ball one quarter turn. The motor is automatically stopped by internal cams striking limit switches. On receipt of a reversing continuous signal, the motor turns in the opposite direction reversing the valve position.
The ball valve is direct mounted to the actuator using the international standard ISO5211 mounting pad. Anti-condensation heater will help protect actuator against damage caused by condensation. Two limit switches are provided to confirm valve position. Manual override can be used to operate valve during setup or with loss of electrical power.
High temperature valve mounting kit available for extended temperature range or wall mounting applications.
Advantages of electric actuated ball valves over other type valves may include: higher flow rates, higher pressures, higher temperatures, wider media compatibility, full port flow path, and reduced water hammer.
Ball Valve Standard FeaturesDirect mount lead free brass valve Full Port for unrestricted flow 316 stainless steel ball and stem Four ball seat design allows for full pressure at any port Energized PTFE ball seats for extended cycle life and reduced torque Leak free triple PTFE/Viton stem seal design Certified per NSF372 and NSF61 for use with potable/drinking water
Electric Actuator Standard FeaturesMulti-voltage capable with auto-voltage sensing Electronic torque limiter Anti-condensation heater LED light gives continuous actuator status indication Manual override with visual valve position indicator Electrical connections via DIN plugs (included) Two dry contact limit switches used to confirm valve position IP65 weatherproof enclosure
Options (see Accessories tab)
The ball valve is direct mounted to the actuator using the international standard ISO5211 mounting pad. Anti-condensation heater will help protect actuator against damage caused by condensation. Two limit switches are provided to confirm valve position. Manual override can be used to operate valve during setup or with loss of electrical power.
High temperature valve mounting kit available for extended temperature range or wall mounting applications.
Advantages of electric actuated ball valves over other type valves may include: higher flow rates, higher pressures, higher temperatures, wider media compatibility, full port flow path, and reduced water hammer.
Ball Valve Standard Features
Electric Actuator Standard Features
Options (see Accessories tab)
Type
3-way L-Port Diverter or Selector
Voltage
24 to 240 Volts AC or 24 to 135 Volts DC (1ph, 50/60 Hz) auto voltage sensing
Current Rating
0.43A @ 110VAC, 0.21A @ 240VAC, 1.98A @ 24VAC
1.63A @ 24VDC (full load amps)
1.63A @ 24VDC (full load amps)
Cycle Time
13 seconds per 90° rotation (no load)
Pipe Size
1-1/4" NPT female
Port Size
Full Port, orifice 1.22 inches, Cv 31
Pressure (Max)
400 PSI CWP non-shock (see P/T chart),
25 PSI steam with high temp. kit, vacuum service to 29" Hg
25 PSI steam with high temp. kit, vacuum service to 29" Hg
Valve Temperature Range
0 to 344 °F (-18 to 173 °C)
Actuator Temperature Range
-4 to +158 °F (-20 to +70 °C)
Valve Body
Lead Free Brass C69300
Ball and Stem
316 stainless steel
Ball Seats
PTFE (Teflon) energized with FKM (viton)
Stem Seals
PTFE (Teflon) with dual FKM (Viton) seals
Duty Cycle
75%
Enclosure
Anti-corrosive polyamide, SS fasteners
Enclosure Rating
IP67 weatherproof, UV protection
Electrical Connections
DIN plugs with cable entry (included), optional 1/2" conduit plugs
Valve Position Confirmation
2 x SPST auxiliary limit switches rated 3A@125/250VAC,
30VDC resistive load
30VDC resistive load
Manual Override
Hand knob
Motor Protection
Electronic over-torque with LED status light
Anti-Condensation Heater
4 watts thermostatically controlled
-
Failsafe Battery KitPrice: $277.00
Buy 3 or more for $246.00 each
Quantity -
Price: $277.00
Buy 3 or more for $246.00 each
Quantity -
Connectors & CablesPrice: $6.40
Buy 10 or more for $5.76 each
Quantity -
Price: $13.84
Buy 10 or more for $12.46 each
Quantity -
Price: $27.08
Buy 10 or more for $24.37 each
Quantity -
Price: $19.84
Buy 10 or more for $17.86 each
Quantity -
High Temperature Mounting KitPrice: $72.00
Buy 6 or more for $64.80 each
Quantity
We provide CAD models in virtually every format. Can't find exactly what you're looking for? Please email sales@valworx.com to request the specific files you need. Include the stock number and any accessories with your request.
Generating the model may take a few minutes.
